View 0804-EVALB02_9052294.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

bel modules 28 turkey court, turkey mill, ashford road maidstone me14 5pp uk ? 2017 bel power solutions, inc +44 1622 757 395 techhelp@belf.com belfuse.com rev f 1 powerline test fixture 0804-EVALB02 the bel 0804-EVALB02 powerline test fixtur e lets you quickly get started testing the 200 and 500 mbps homeplug ? av bel powerline modules. the 0804-EVALB02 powerline test fixture provides all the required circuitry (mains coupler, power supply, ze ro- crossing detection, protection and ethernet interface) for i nterfacing a bel powerline module. you just need an ethernet cable and a two conductor medium to make the powerline test fixture operate as a gatewa y between an ethernet network and a powerline network. key features & benefits ? ?? ? compatible with bel 0804-5000-18/-24/- 25/a50/e50 powerline modules ? ?? ? fully configurable ac/dc/dry wire operation ? ?? ? wide range 19-75v dcdc convertor included ? ?? ? led status indicators ? ?? ? push buttons for pairing, reset & factory defaults ? ?? ? 5 ethernet ports models part number description 0804-EVALB02 homeplug? av powerline test fixture (2 00/500mbits)
powerline test fixture 0804-EVALB02 user manual techhelp@belf.com belpowersolutions.com 2 evaluation board block diagram led indicators reference colour signal route default behavior d5 green powerline module: gpio11 (when sip is pres ent) power d4 yellow powerline module: gpio8 powerline tx/rx link d3 orange ethernet switch ethernet tx/rx link d2 blue expansion port reserved
powerline test fixture 0804-EVALB02 user manual techhelp@belf.com belpowersolutions.com 3 push buttons reference name signal route use sw1 simple connect powerline module: gpio1 simple c onnect C pairing button. sw2 factory default powerline module: gpio2 restoring the factory default pib. sw3 reset reset press this button to reset the boar d. 5mm pitch spacing terminal block reference use view j5 dc power in (support range 19-75v dc/dc) j8 hpav communication terminal * use under safety cover. with exposed board due to safety reason please do not use higher voltage tha n 24v. ethernet connectors reference description view j2 rj45 magjack? 10/100/1000base-t ethernet shielde d connector. j3, j4 2 port rj45 magjack? 10/100/1000base-t ethernet shi elded connector. pin number pin name direction electrical characteristics 1 bi_da+ bi-directional pair a + standard ieee 802.3 2 bi_da- bi-directional pair a - standard ieee 802.3 3 bi_db+ bi-directional pair b + standard ieee 802.3 4 bi_dc+ bi-directional pair c + standard ieee 802.3 5 bi_dc- bi-directional pair c - standard ieee 802.3 6 bi_db- bi-directional pair b - standard ieee 802.3 7 bi_dd+ bi-directional pair d + standard ieee 802.3 8 bi_dd- bi-directional pair d - standard ieee 802.3
powerline test fixture 0804-EVALB02 user manual techhelp@belf.com belpowersolutions.com 4 powerline module connector manufacturers part number reference description view samtec sms-150-01-g-s j1 50 ways, 1 row, through holes micro socket. pitch 1.27mm. insertion force 8oz; withdrawal force 6 oz. this connector is to be directly connected to 200mb ps powerline module: 0804-5000-18, 0804-5000-24, 08 04-5000-25 or 500mbps powerline module: 0804-5000a50 or 0804-5000 e50. the pin 1 of the powerline module must be conn ected to pin 1 of j1. pin number pin name mii 200mbps rgmii 500mbps type description 1 vdd vdd pwr +3.3v 2 vss vss pwr ground 3 vdd vdd pwr +3.3v 4 vss vss pwr ground 5 vdd vnet_io pwr 200mbps: vdd +3.3v 500mbps: rgmii voltage level: +2.5v / +3.3v 6 tx+ txrx+ i/o 200mbps: differential tx+ signal, connects to coupl ing transformer 500mbps: differential txrx+ signal, connects to cou pling transformer 7 tx- txrx- i/o 200mbps: differential tx- signal, connects to coupl ing transformer 500mbps: differential txrx- signal, connects to cou pling transformer 8 vss vss pwr ground 9 rx+ reserved i/o 200mbps: differential rx signal, connects to coupli ng transformer 500mbps: reserved pin 10 rx- reserved i/o 200mbps: differential rx signal, connects to coupli ng transformer 500mbps: reserved pin 11 reset# reset# i resets all ic logic when low 12 gpio0 gpio0 i/o 200mbps: strap - n/a 500mbps: strap - enet_sel[0] 13 gpio1 gpio1 i/o 200mbps: strap - n/a; push-button: simple connect 500mbps: strap: enet_sel[1]; push-button: simple co nnect 14 gpio2 gpio2 i/o 200mbps: strap - n/a; push-button: factory default 500mbps: strap - anen; push-button: factory default 15 gpio3 reserved i/o 200mbps: strap - isodef 500mbps: reserved pin 16 gpio4 gpio4 i/o 200mbps: strap - speed 500mbps: strap - speed_sel[0] 17 gpio5 gpio5 i/o 200 / 500mbps: strap - md_a3 18 gpio6 gpio6 i/o 200 / 500mbps: strap - cfg_sel 19 gpio7 gpio7 i/o 200 / 500mbps: strap - md_a4 20 gpio8 gpio8 i/o 200 / 500mbps: strap - mp_sel; led: powerline tx/rx link
powerline test fixture 0804-EVALB02 user manual techhelp@belf.com belpowersolutions.com 5 pin number pin name mii 200mbps rgmii 500mbps type description 21 gpio9 gpio3 i/o 200mbps: strap - n/a (pull-down); led: ethernet tx/ rx link 500mbps: strap - isodef; led: ethernet tx/rx link 22 gpio10 gpio10 i/o 200 / 500mbps: strap - bm_sel 23 gpio11 gpio11 i/o 200mbps: strap - n/a 500mbps: strap - speed_sel[1]; led: power 24 zc_in zc_in i/o zero-cross detection signal 25 mdio mdio i/o management data interface data lin e 26 mdc mdc o mac /i phy management data interface clock line 27 reserved reserved - reserved pin 28 reserved reserved - reserved pin (pull-down for 200mbps powerline module) 29 vss vss pwr ground 30 mrx_d0 rd0 i mac /o phy mii / rgmii: receive data bits (mac) 31 mrx_d1 rd1 i mac /o phy mii / rgmii: receive data bits (mac) 32 mrx_d2 rd2 i mac /o phy mii / rgmii: receive data bits (mac) 33 mrx_d3 rd3 i mac /o phy mii / rgmii: receive data bits (mac) 34 col - i mac /o phy mii: collision detected 35 mrx_clk rxc i mac /o phy mii / rgmii: receive clock (mac) 36 vss vss ground ground 37 mrx_err - i mac /o phy mii: receive error (mac) 38 mrx_dv rx_ctl i mac /o phy mii: receive data valid (mac) rgmii: receive control signal (mac) 39 mtx_d0 td0 o mac /i phy mii / rgmii: transmit data bits (mac) 40 mtx_d1 td1 o mac /i phy mii / rgmii: transmit data bits (mac) 41 mtx_d2 td2 o mac /i phy mii / rgmii: transmit data bits (mac) 42 mtx_d3 td3 o mac /i phy mii / rgmii: transmit data bits (mac) 43 crs - i mac /o phy mii: carrier sense 44 mtx_clk txc mii: i mac /o phy rgmii: o mac /i phy mii: transmit clock (mac) rgmii: trans mit clock (mac) 45 mtx_en tx_ctl o mac /i phy mii: transmit enable (mac) rgmii: transmit control signal (mac) 46 vss vss pwr ground 47 phy_rst# phy_rst# o reset ethernet phy 48 vss vss pwr ground 49 phy_clk phy_clk o strap: duplex; 25mhz clock for ethernet phy 50 vss vss pwr ground
powerline test fixture 0804-EVALB02 user manual techhelp@belf.com belpowersolutions.com 6 the pin-strapping for 200mbps powerline modules header j1 pin no signal name strap function 0804-EVALB02 strap 0804-EVALB02 strap description 12 gpio0 n/a pull-up n/a 13 gpio1 n/a pull-up n/a 14 gpio2 n/a pull-up n/a 15 gpio3 isodef pull-down* mii phy mode isolate selection: normal operation 16 gpio4 speed pull-up mii phy mode speed selection : 100mbps 17 gpio5 md_a3 pull-up mii phy mode management address selection md_a[4:3] : 0x08 19 gpio7 md_a4 pull-down 22 gpio10 bm_sel pull-up* boot and sdram configuration straps [bm_sel/cfg_sel ]: load sdram configuration and boot code from flash 18 gpio6 cfg_sel pull-up* 20 gpio8 mp_sel pull-down* mii mode selection: phy mode 21 gpio9 n/a pull-down pull down 23 gpio11 n/a pull-down n/a 49 phy_clk duplex pull-up mii phy mode duplex selec tion: full duplex * powerline module default strapping changed, (conf iguration forced by 0804-EVALB02) the pin-strapping for 500mbps powerline modules header j1 pin no signal name strap function 0804-EVALB02 strap 0804-EVALB02 strap description 12 gpio0 enet_sel[0] pull-down* 10/100/1000 rgmii C no delay on rx clock 13 gpio1 enet_sel[1] pull-down* 14 gpio2 anen pull-up phy mode auto-negotiate: enabled 21 gpio3 isodef pull-down rgmii phy mode isolate se lection: normal operation 16 gpio4 speed_sel[0] pull-down* rgmii phy mode speed selection: 1000mbps 23 gpio11 speed_sel[1] pull-up* 17 gpio5 md_a3 pull-up rgmii phy mode management address selection md_a[4: 3]: 0x08 19 gpio7 md_a4 pull-down 22 gpio10 bm_sel pull-up boot and dram configuration straps [bm_sel/cfg_sel] : load dram configuration and boot code from flash 18 gpio6 cfg_sel pull-up 20 gpio8 mp_sel pull-down* rgmii mode selection: ph y mode 49 phy_clk duplex pull-up mii phy mode duplex selection: full duplex * powerline module default strapping changed, (conf iguration forced by 0804-EVALB02)
powerline test fixture 0804-EVALB02 user manual techhelp@belf.com belpowersolutions.com 7 evaluation board layout and connections pl (hpav) 5x ethernet ports sfp daughter board port 0804-5000-18/24/50/51 sip port power led reserved ethernet link powerline link + C dc in simple connect factory default reset
powerline test fixture 0804-EVALB02 user manual techhelp@belf.com belpowersolutions.com 8 getting started the evaluation board is able to accept one of the f ollowing bel powerline modules via connector j1: ? ?? ? 0804-5000-18 (mii; 200mbps) ? ?? ? 0804-5000-24 (mii; 200mbps) ? ?? ? 0804-5000-25 (mii; 200mbps) ? ?? ? 0804-5000a50 (rgmii; 500mbps) ? ?? ? 0804-5000e50 (rgmii; 500mbps) the board requires a 19-75v dc input (not mains as on previous evaluation boards). communications lines can be connected to either a d ry wire, ac, dc separate line via the connector j8. the on board coupling transformer (bel 0557-7700-42 ) provides isolation suitable for ac mains operatio n. caution: to prevent an electrical shock, do not sup ply high voltage to the board without protective co ver led indicators are provided to show the status of t he evaluation board, the function of these are: d5 - power led: operates when the board is powered and the dcdc convertor is functioning correctly d4 - powerline link: operates when a powerline conn ection is made between two or more powerline module s d3 - ethernet link: operates when connectivity to a n ethernet host is detected on any of the ethernet ports d2 C reserved: no used. an ethernet phy solution is implemented using one p ort of a multiport gigabit switch (qca8337n 7-port gigabit ethernet switch). all of the ports can be utilized. the evaluation board will function as an ethernet t o powerline bridge with no further configuration. expected performance performance of the evaluation board will depend on the powerline module used, the packet size and the communications medium attenuation. basic testing should be conducted with a cable no s horter than 2 meters. in some cases, a very short c able can cause performance degradation. for a short ideal cable (~2 meters) the following phy rates should be achievable: 0804-5000-18/-24/-25 (200mbps technology): phy rat e 130-150mbps (actual transfer rate ~80mbps) 0804-5000a50/e50 (500mbps technology): phy rate 32 0-380mbps (actual transfer rate ~200mbps) open source qualcomm atheros open powerline toolkit is freely available on the github web site and can be used to read phy rate and manage powerline devices.
powerline test fixture 0804-EVALB02 user manual techhelp@belf.com belpowersolutions.com 9 to test the network performance, you can use common ly used open source network testing tool iperf, wit h graphical frontend jperf. before starting the program, please complete the fo llowing configuration: requirements: ? ?? ? 2 x pc with network card ? ?? ? 2 x 0804-EVALB02 test fixture ? ?? ? 2 x 0804-5000-18/-24/-25/a50/e50 powerline sip ? ?? ? 2 x 24v bench power supply ? ?? ? cable to create hpav network 1. configure static ip address: pc1: ? ip address: 192.168.100.1 ? subnet mask: 255.255.255.0 pc2: ? ip address: 192.168.100.2 ? subnet mask: 255.255.255.0 2. run the jperf and change the program setting: pc1: ? ipref mode: server ? listen port: 7000 ? num connections: 5 ? protocol: tcp ? tcp window size: 64 kbytes pc2: ? ipref mode: client ? server address: 192.168.100.1 0804-EVALB02 +powerline sip #1 rj-45 pc1 server 0804-EVALB02 +powerline sip #2 rj-45 ac mains / dc or dry wire (hpav network) hpav hpav pc2 client bench psu 24v bench psu 24v dc power in dc power in
powerline test fixture 0804-EVALB02 user manual techhelp@belf.com belpowersolutions.com 10 ? listen port: 7000 ? parallel streams: 5 ? protocol: tcp ? tcp window size: 64 kbytes 3. click run iperf! button, on pc1 (server) and pc2 (client). example test results for 0804-5000-24 sip module
powerline test fixture 0804-EVALB02 user manual techhelp@belf.com belpowersolutions.com 11 example test results for 0804-5000e50 sip module

▲Up To Search▲

Price & Availability of 0804-EVALB02

	To Download 0804-EVALB02 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .